Despite the recent release of these Tesla EVs — and the little road time they’ve been subjected to — Cybertrucks are already developing imperfections on their body panels, leading owners to debate what’s causing the early signs of rust on forums. From Futurism:
One Cybertruck Owners Club forum member says they started noticing small orange flecks appearing on his truck after driving it in the rain for just two days.
“Just picked up my Cybertruck today,” they wrote. “The advisor specifically mentioned the cybertrucks develop orange rust marks in the rain and that required the vehicle to be buffed out.”
The Cybertruck owner posted followup photos after washing the vehicle down with soap, and they didn’t inspire much confidence, showing body panels already pockmarked with small orange spots.
Cross post from https://lemmy.world/comment/7544395
For what it’s worth you don’t have to spend much time around stainless steel to realize the word ‘stainless’ isn’t literal. I bet you exactly 0 knife nerds actually believed this thing wasn’t going to rust.
Stainless doesn’t rust. Stainless alloys do. Knives are an alloy because they need certain properties to be able to sharpen them properly and hold an edge.
Medical stainless doesn’t rust and whatever the hell my kitchen sink is doesn’t either.
“Surgical” stainless - a marketing term - will rust simply because it’s still an alloy of chromium and steels - it just takes far longer than the higher carbon steel alloys because of the lower carbon content. And yes, scalpel blades are made from high carbon stainless alloys that WILL rust if not properly stored - they are single use items and tossed when done being used once.
Your stainless sink is probably made from some 304 stainless alloy due to it’s deep draw properties thanks to the extra nickle content. Things marked “Surgical” stainless would fall into this type of alloy. But 300 series stainless steels still contain about .05% carbon which is still enough to cause eventual rusting or staining.
You do know that more than scalpels are used right? Things that are put into autoclaves and used over and over and over again.
Marine stainless will absolutely rust. I bet surgical stainless will to next to the ocean.
Yes, yes it will. Since “surgical stainless” is a marketing hype term, (just like something marked “billet” or “military grade”), it’s just a lower carbon/higher nickle content stainless. Marine stainless steels are most often cheaper 300 series steels.
I never said “surgical stainless”. I said medical, as in the tools that are used in the medical space. These are typically reused after going through an autoclave.
Medical grade and surgical grade are just marketing terms. It’s all 304 and 316 (sometimes 440 or 420)
There are ASTM standards for biocompatible metals.
https://www.researchgate.net/figure/Corrosion-morphologies-of-316L-stainless-steel-after-exposed-in-South-Sea-atmospheric-for_fig2_325407491
Good knives rust, bad knives don’t. You need high iron to hone a perfect edge properly. You can still resharpen a shitty knife, your grocery butcher will likely do it for free, but it will never have the same edge as a properly honed good knife.
Do you hone it 1000 times, knife sama?
Just quickly before use. If you keep up with it, you rarely ever need to actually sharpen it.
All stainless steels are alloys.
You’re correct, I should have said “some”
Knifes are different though, as that is a different stainless steel alloy. I don’t remember the specifics, but something about higher carbon content so it can be hardened? This is why you shouldn’t put knifes into a dishwasher, they don’t like the salt and will get pitted over time.
Nevertheless, no “normal” stainless is actually immune to rust or general corrosion anyway. It also depends on the environment (ask boat folks about this one), specifically if oxygen can get to it. And salt just makes everything 100x worse, too.
Closest you get to real rust proof steel is nitrogen steels, which are used for diving knives. Super super hard though, doubt it’d make a good auto body, I’d imagine such a thing would be prone to cracking. Expensive too. I’m gonna say Daddy Elon’s best bet is to slap regular painted body panels on it and take the hit. I think we all know what he’s not going to do though.
Even the nitrogen alloy steels used for diving knives will corrode. It just takes a lot longer than the normal high carbon stainless alloys.
Water is the universal solvent…
If/when BYD builds their first manufacturing plant and starts selling, Musk might change his mind about that.