This is getting ridiculous. While I only have an associates degree in CAD and machine design, I’m pretty sure I can pick out when a piece of 4040 extrusion is BENT, and i own and know how to use engineering squares. It wasn’t an assembly mistake on my part. Since you buy them literally all the time on Ebay, someone must’ve snatched mine up before you could, since this NEVER happens. By your own admission, that extruder, from my generation, was junk. Yes it was only a $15 fix, and really, if you’re going to get into this hobby you should be able to swap this part out, but the point stands-
First machine I bought was an OOB failure. When I brought it back to the store they opened the box and confirmed this with me. They did not need a finely honed straightedge to confirm it, the top gantry extrusion was bent.
Round two, the machine did okay, aside from the bed seemingly “losing” it’s trimming. I purchased the “yellow springs” and installed them. This, at the time, seemed to resolve the issue. Until it didnt. At that point, I purchased and installed Creality’s own ABL, I believe it was the CR touch, but you’ll surely correct me if I’m wrong, after looking into several reviews/yt videos and multiple installation guides (somewhere during this time the extruder went, and yes, this was an easy fix with the red aluminum one). This is when I learned that the glass PEI bed that came with my machine was no longer flat. Fair enough, I figured this was a consumable part and bought another one. This did solve the problem again… until it didn’t. This one had warped as well, as confirmed with a good, flat straightedge (an 18" Starrett 385, to be exact). It wasn’t from improperly tensioned belts. Rather than attack someone personally over their experience, you scream Creality’s praises on the internet and seem to insist that my experiences could not have happened. Sure, I bet you and your team are able to resurrect broken down machines, and that is fantastic. It keeps junk from filling up landfills and may even be able to get someone into the hobby at a lower price point. I commend you on this, honestly. However, after dumping time and money into the second machine Iexperienced from them, I decided it was no longer worth the effort. Mind you, these things all happened in about 8-9 months. I got some pretty good prints from it, but I also got a lot of failures, and when those kept piling up I cut my losses. As I’ve repeatedly stated, this was MY experience. Yours has clearly been different. I’m fully aware that scores of people likely fuck up these machines by putting them together incorrectly- I assure you this was not the case on mine.
This is getting ridiculous. While I only have an associates degree in CAD and machine design, I’m pretty sure I can pick out when a piece of 4040 extrusion is BENT, and i own and know how to use engineering squares. It wasn’t an assembly mistake on my part. Since you buy them literally all the time on Ebay, someone must’ve snatched mine up before you could, since this NEVER happens. By your own admission, that extruder, from my generation, was junk. Yes it was only a $15 fix, and really, if you’re going to get into this hobby you should be able to swap this part out, but the point stands-
First machine I bought was an OOB failure. When I brought it back to the store they opened the box and confirmed this with me. They did not need a finely honed straightedge to confirm it, the top gantry extrusion was bent.
Round two, the machine did okay, aside from the bed seemingly “losing” it’s trimming. I purchased the “yellow springs” and installed them. This, at the time, seemed to resolve the issue. Until it didnt. At that point, I purchased and installed Creality’s own ABL, I believe it was the CR touch, but you’ll surely correct me if I’m wrong, after looking into several reviews/yt videos and multiple installation guides (somewhere during this time the extruder went, and yes, this was an easy fix with the red aluminum one). This is when I learned that the glass PEI bed that came with my machine was no longer flat. Fair enough, I figured this was a consumable part and bought another one. This did solve the problem again… until it didn’t. This one had warped as well, as confirmed with a good, flat straightedge (an 18" Starrett 385, to be exact). It wasn’t from improperly tensioned belts. Rather than attack someone personally over their experience, you scream Creality’s praises on the internet and seem to insist that my experiences could not have happened. Sure, I bet you and your team are able to resurrect broken down machines, and that is fantastic. It keeps junk from filling up landfills and may even be able to get someone into the hobby at a lower price point. I commend you on this, honestly. However, after dumping time and money into the second machine Iexperienced from them, I decided it was no longer worth the effort. Mind you, these things all happened in about 8-9 months. I got some pretty good prints from it, but I also got a lot of failures, and when those kept piling up I cut my losses. As I’ve repeatedly stated, this was MY experience. Yours has clearly been different. I’m fully aware that scores of people likely fuck up these machines by putting them together incorrectly- I assure you this was not the case on mine.